re.visp.net.lb) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #7 SMP PREEMPT Mon Jan 7 06:58:04 EET 2008 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000100 - 000000000008f000 (usable) [ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfd99000 (usable) [ 0.000000] BIOS-e820: 00000000cfd99000 - 00000000cfda6000 (reserved) [ 0.000000] BIOS-e820: 00000000cfda6000 - 00000000cfe3c000 (usable) [ 0.000000] BIOS-e820: 00000000cfe3c000 - 00000000cfe96000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfe96000 - 00000000cfe9b000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cfe9b000 - 00000000cfe9c000 (usable) [ 0.000000] BIOS-e820: 00000000cfe9c000 - 00000000cfef2000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfef2000 - 00000000cfeff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cfeff000 - 00000000cff00000 (usable) [ 0.000000] BIOS-e820: 00000000cff00000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 000000012c000000 (usable) [ 0.000000] Warning only 896MB will be used. [ 0.000000] Use a HIGHMEM64G enabled kernel. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000fe200 [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] Entering add_active_range(0, 0, 229376) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 229376 [ 0.000000] On node 0 totalpages: 229376 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL ) [ 0.000000] ACPI: RSDT CFEFD038, 0050 (r1 INTEL DG965SS 6B7 1000013) [ 0.000000] ACPI: FACP CFEFC000, 0074 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: DSDT CFEF7000, 41AA (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: FACS CFE9C000, 0040 [ 0.000000] ACPI: APIC CFEF6000, 0078 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: WDDT CFEF5000, 0040 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: MCFG CFEF4000, 003C (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: ASF! CFEF3000, 00A6 (r32 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: HPET CFEF2000, 0038 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE9A000, 020C (r1 INTEL CpuPm 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE99000, 0175 (r1 INTEL Cpu0Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE98000, 0175 (r1 INTEL Cpu1Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE97000, 0175 (r1 INTEL Cpu2Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE96000, 0175 (r1 INTEL Cpu3Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ff00000) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227584 [ 0.000000] Kernel command line: root=/dev/sdb2 [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2397.655 MHz processor. [ 500.771561] Console: colour VGA+ 80x25 [ 500.771563] console [tty0] enabled [ 500.775787] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 500.776043] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 500.784856] Memory: 871712k/917504k available (1971k kernel code, 45320k reserved, 797k data, 212k init, 0k highmem) [ 500.784962] virtual kernel memory layout: [ 500.784963] fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB) [ 500.784964] vmalloc : 0xf8800000 - 0xfffb3000 ( 119 MB) [ 500.784965] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 500.784965] .init : 0xc03bb000 - 0xc03f0000 ( 212 kB) [ 500.784966] .data : 0xc02ece59 - 0xc03b45ac ( 797 kB) [ 500.784967] .text : 0xc0100000 - 0xc02ece59 (1971 kB) [ 500.785403] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 500.785700] hpet clockevent registered [ 500.845691] Calibrating delay using timer specific routine.. 4797.85 BogoMIPS (lpj=2398929) [ 500.845854] Mount-cache hash table entries: 512 [ 500.845996] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 500.846002] monitor/mwait feature present. [ 500.846064] using mwait in idle threads. [ 500.846127] CPU: L1 I cache: 32K, L1 D cache: 32K [ 500.846214] CPU: L2 cache: 4096K [ 500.846276] CPU: Physical Processor ID: 0 [ 500.846337] CPU: Processor Core ID: 0 [ 500.846399] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 500.846405] Intel machine check architecture supported. [ 500.846469] Intel machine check reporting enabled on CPU#0. [ 500.846534] Compat vDSO mapped to ffffe000. [ 500.846602] Checking 'hlt' instruction... OK. [ 500.849952] SMP alternatives: switching to UP code [ 500.850516] ACPI: Core revision 20070126 [ 500.852097] Parsing all Control Methods: [ 500.852187] Table [DSDT](id 0001) - 610 Objects with 62 Devices 154 Methods 38 Regions [ 500.852385] Parsing all Control Methods: [ 500.852468] Table [SSDT](id 0002) - 10 Objects with 0 Devices 4 Methods 0 Regions [ 500.852645] Parsing all Control Methods: [ 500.852735] Table [SSDT](id 0003) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 500.852912] Parsing all Control Methods: [ 500.852996] Table [SSDT](id 0004) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 500.853172] Parsing all Control Methods: [ 500.853257] Table [SSDT](id 0005) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 500.853433] Parsing all Control Methods: [ 500.853517] Table [SSDT](id 0006) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 500.853674] tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired [ 500.853833] evxfevnt-0079 [00] enable : System is already in ACPI mode [ 500.853999] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 500.854121] SMP alternatives: switching to SMP code [ 500.854511] Booting processor 1/1 eip 3000 [ 500.864927] Initializing CPU#1 [ 500.924671] Calibrating delay using timer specific routine.. 4795.20 BogoMIPS (lpj=2397600) [ 500.924676] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 500.924680] monitor/mwait feature present. [ 500.924682] CPU: L1 I cache: 32K, L1 D cache: 32K [ 500.924683] CPU: L2 cache: 4096K [ 500.924685] CPU: Physical Processor ID: 0 [ 500.924686] CPU: Processor Core ID: 1 [ 500.924687] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 500.924690] Intel machine check architecture supported. [ 500.924693] Intel machine check reporting enabled on CPU#1. [ 500.925249] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 500.925971] Total of 2 processors activated (9593.05 BogoMIPS). [ 500.926170] ENABLING IO-APIC IRQs [ 500.926389] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 501.037750] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 501.057845] Brought up 2 CPUs [ 501.057922] CPU0 attaching sched-domain: [ 501.057924] domain 0: span 00000003 [ 501.057925] groups: 00000001 00000002 [ 501.057928] CPU1 attaching sched-domain: [ 501.057929] domain 0: span 00000003 [ 501.057930] groups: 00000002 00000001 [ 501.058081] net_namespace: 64 bytes [ 501.058437] NET: Registered protocol family 16 [ 501.058603] ACPI: bus type pci registered [ 501.058726] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved [ 501.058791] PCI: Not using MMCONFIG. [ 501.060216] PCI: Using configuration type 1 [ 501.060278] Setting up standard PCI resources [ 501.067016] evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 [ 501.067733] evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 4 Runtime GPEs in this block [ 501.067888] ACPI: EC: Look up EC in DSDT [ 501.069136] Completing Region/Field/Buffer/Package initialization:........................................................................ [ 501.071522] Initialized 32/38 Regions 0/0 Fields 25/25 Buffers 15/35 Packages (649 nodes) [ 501.071680] Initializing Device/Processor/Thermal objects by executing _INI methods:. [ 501.071825] Executed 1 _INI methods requiring 0 _STA executions (examined 68 objects) [ 501.071998] ACPI: Interpreter enabled [ 501.072061] ACPI: (supports S0 S3 S5) [ 501.072202] ACPI: Using IOAPIC for interrupt routing [ 501.075588] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 501.076341] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO [ 501.076408] PCI quirk: region 0500-053f claimed by ICH6 GPIO [ 501.077055] PCI: Transparent bridge - 0000:00:1e.0 [ 501.077182] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 501.077450] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 501.077654] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 501.077738] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 501.077822] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT] [ 501.077909] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] [ 501.077993] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 501.082388] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.082857] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.083320] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.083783] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.084248] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.084713] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.085178] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.085640] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 501.086130] Linux Plug and Play Support v0.97 (c) Adam Belay [ 501.086214] pnp: PnP ACPI init [ 501.086280] ACPI: bus type pnp registered [ 501.088275] pnp: PnP ACPI: found 11 devices [ 501.088338] ACPI: ACPI bus type pnp unregistered [ 501.088537] SCSI subsystem initialized [ 501.088625] libata version 3.00 loaded. [ 501.088692] PCI: Using ACPI for IRQ routing [ 501.089512] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 501.093909] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 501.094083] hpet0: 3 64-bit timers, 14318180 Hz [ 501.095171] ACPI: RTC can wake from S4 [ 501.095725] Time: tsc clocksource has been installed. [ 501.097998] system 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved [ 501.098076] system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved [ 501.098142] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved [ 501.098208] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved [ 501.098273] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved [ 501.098339] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 501.098404] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved [ 501.098470] system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved [ 501.098536] system 00:01: iomem range 0xc0000-0xdffff could not be reserved [ 501.098601] system 00:01: iomem range 0xe0000-0xfffff could not be reserved [ 501.098672] system 00:06: ioport range 0x500-0x53f has been reserved [ 501.098736] system 00:06: ioport range 0x400-0x47f has been reserved [ 501.098801] system 00:06: ioport range 0x680-0x6ff has been reserved [ 501.129201] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0 [ 501.129300] PCI: Bridge: 0000:00:01.0 [ 501.129363] IO window: 2000-2fff [ 501.129425] MEM window: e0000000-e1ffffff [ 501.129488] PREFETCH window: d0000000-dfffffff [ 501.129552] PCI: Bridge: 0000:00:1c.0 [ 501.129614] IO window: disabled. [ 501.129677] MEM window: disabled. [ 501.129740] PREFETCH window: disabled. [ 501.129804] PCI: Bridge: 0000:00:1c.1 [ 501.129867] IO window: 1000-1fff [ 501.129931] MEM window: e2000000-e20fffff [ 501.129996] PREFETCH window: disabled. [ 501.130060] PCI: Bridge: 0000:00:1c.2 [ 501.130121] IO window: disabled. [ 501.130185] MEM window: disabled. [ 501.130248] PREFETCH window: disabled. [ 501.130312] PCI: Bridge: 0000:00:1c.3 [ 501.130373] IO window: disabled. [ 501.130437] MEM window: disabled. [ 501.130499] PREFETCH window: disabled. [ 501.130563] PCI: Bridge: 0000:00:1c.4 [ 501.130625] IO window: disabled. [ 501.130688] MEM window: disabled. [ 501.130751] PREFETCH window: disabled. [ 501.130815] PCI: Bridge: 0000:00:1e.0 [ 501.130877] IO window: disabled. [ 501.130940] MEM window: disabled. [ 501.131004] PREFETCH window: disabled. [ 501.131077] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 501.131202] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 501.131216] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 501.131341] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 501.131355] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16 [ 501.131480] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 501.131494] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 501.131619] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 501.131633] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 [ 501.131758] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 501.131772] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17 [ 501.131897] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 501.131905] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 501.131925] NET: Registered protocol family 2 [ 501.142236] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 501.142463] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 501.142849] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 501.143109] TCP: Hash tables configured (established 131072 bind 65536) [ 501.143179] TCP reno registered [ 501.146607] Machine check exception polling timer started. [ 501.146848] IA-32 Microcode Update Driver: v1.14a [ 501.147244] Total HugeTLB memory allocated, 0 [ 501.147447] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 501.147547] io scheduler noop registered [ 501.147619] io scheduler cfq registered (default) [ 501.147775] Boot video device is 0000:01:00.0 [ 501.147845] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 501.147870] assign_interrupt_mode Found MSI capability [ 501.147952] Allocate Port Service[0000:00:01.0:pcie00] [ 501.148009] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 501.148041] assign_interrupt_mode Found MSI capability [ 501.148128] Allocate Port Service[0000:00:1c.0:pcie00] [ 501.148153] Allocate Port Service[0000:00:1c.0:pcie02] [ 501.148214] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 501.148248] assign_interrupt_mode Found MSI capability [ 501.148335] Allocate Port Service[0000:00:1c.1:pcie00] [ 501.148359] Allocate Port Service[0000:00:1c.1:pcie02] [ 501.148425] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 501.148457] assign_interrupt_mode Found MSI capability [ 501.148543] Allocate Port Service[0000:00:1c.2:pcie00] [ 501.148568] Allocate Port Service[0000:00:1c.2:pcie02] [ 501.148630] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 501.148661] assign_interrupt_mode Found MSI capability [ 501.148748] Allocate Port Service[0000:00:1c.3:pcie00] [ 501.148772] Allocate Port Service[0000:00:1c.3:pcie02] [ 501.148833] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 501.148865] assign_interrupt_mode Found MSI capability [ 501.148952] Allocate Port Service[0000:00:1c.4:pcie00] [ 501.148976] Allocate Port Service[0000:00:1c.4:pcie02] [ 501.149202] input: Power Button (FF) as /class/input/input0 [ 501.149268] ACPI: Power Button (FF) [PWRF] [ 501.149379] input: Sleep Button (CM) as /class/input/input1 [ 501.149446] ACPI: Sleep Button (CM) [SLPB] [ 501.149700] ACPI: Processor [CPU0] (supports 8 throttling states) [ 501.149890] ACPI: Processor [CPU1] (supports 8 throttling states) [ 501.150012] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 501.150170] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 501.173690] hpet_resources: 0xfed00000 is busy [ 501.173708] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI [ 501.173773] e100: Copyright(c) 1999-2006 Intel Corporation [ 501.174122] ahci 0000:00:1f.2: version 3.0 [ 501.174136] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19 [ 501.411009] Switched to high resolution mode on CPU 1 [ 501.411831] Switched to high resolution mode on CPU 0 [ 502.173623] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 502.173729] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part [ 502.173799] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 502.173974] scsi0 : ahci [ 502.174081] scsi1 : ahci [ 502.174186] scsi2 : ahci [ 502.174288] scsi3 : ahci [ 502.174390] scsi4 : ahci [ 502.174491] scsi5 : ahci [ 502.174654] ata1: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125100 irq 217 [ 502.174755] ata2: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125180 irq 217 [ 502.174857] ata3: DUMMY [ 502.174917] ata4: DUMMY [ 502.174979] ata5: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125300 irq 217 [ 502.175079] ata6: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125380 irq 217 [ 502.630591] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 502.668646] ata1.00: ATA-7: ST3200820AS, 3.AAE, max UDMA/133 [ 502.668715] ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 502.726947] ata1.00: configured for UDMA/133 [ 503.182589] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 503.223102] ata2.00: ATA-7: ST3200820AS, 3.AAE, max UDMA/133 [ 503.223170] ata2.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 503.281402] ata2.00: configured for UDMA/133 [ 503.583549] ata5: SATA link down (SStatus 0 SControl 300) [ 503.886536] ata6: SATA link down (SStatus 0 SControl 300) [ 503.886697] scsi 0:0:0:0: Direct-Access ATA ST3200820AS 3.AA PQ: 0 ANSI: 5 [ 503.886899] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) [ 503.886971] sd 0:0:0:0: [sda] Write Protect is off [ 503.887034] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 503.887046] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 503.887180] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) [ 503.887251] sd 0:0:0:0: [sda] Write Protect is off [ 503.887314] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 503.887326] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 503.887427] sda: sda1 [ 503.907705] sd 0:0:0:0: [sda] Attached SCSI disk [ 503.907837] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 503.907978] scsi 1:0:0:0: Direct-Access ATA ST3200820AS 3.AA PQ: 0 ANSI: 5 [ 503.908152] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB) [ 503.908223] sd 1:0:0:0: [sdb] Write Protect is off [ 503.908286] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 503.908299] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 503.908425] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB) [ 503.908496] sd 1:0:0:0: [sdb] Write Protect is off [ 503.908562] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 503.908575] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 503.908676] sdb: sdb1 sdb2 sdb3 sdb4 [ 503.929314] sd 1:0:0:0: [sdb] Attached SCSI disk [ 503.929424] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 503.929604] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 503.929747] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 503.929773] scsi6 : pata_marvell [ 503.929879] scsi7 : pata_marvell [ 503.929974] ata7: PATA max UDMA/100 cmd 0x1018 ctl 0x1024 bmdma 0x1000 irq 17 [ 503.930039] ata8: DUMMY [ 503.930114] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00 [ 504.235878] ata7.00: ATAPI: HL-DT-ST DVDRAM GSA-H42N, RL00, max UDMA/66 [ 504.392875] ata7.00: configured for UDMA/66 [ 504.396336] scsi 6:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H42N RL00 PQ: 0 ANSI: 5 [ 504.413815] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 504.413919] Uniform CD-ROM driver Revision: 3.20 [ 504.414067] sr 6:0:0:0: Attached scsi CD-ROM sr0 [ 504.414117] sr 6:0:0:0: Attached scsi generic sg2 type 5 [ 504.414301] PNP: PS/2 Controller [PNP0f03:PS2M] at 0x60,0x64 irq 12 [ 504.414365] PNP: PS/2 controller doesn't have KBD irq; using default 1 [ 504.417318] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 504.417384] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 504.417509] mice: PS/2 mouse device common for all mice [ 504.597100] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) [ 505.237967] input: ImPS/2 Generic Wheel Mouse as /class/input/input2 [ 505.247403] iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0460) [ 505.247553] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 505.247630] iTCO_vendor_support: vendor-support=0 [ 505.247735] TCP cubic registered [ 505.247803] NET: Registered protocol family 1 [ 505.248626] NET: Registered protocol family 17 [ 505.248692] Using IPI No-Shortcut mode [ 505.248835] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 505.248899] EDD information not available. [ 505.254610] EXT3-fs: INFO: recovery required on readonly filesystem. [ 505.254679] EXT3-fs: write access will be enabled during recovery. [ 514.768711] kjournald starting. Commit interval 5 seconds [ 514.768719] EXT3-fs: recovery complete. [ 514.773493] EXT3-fs: mounted filesystem with ordered data mode. [ 514.773572] VFS: Mounted root (ext3 filesystem) readonly. [ 514.773720] Freeing unused kernel memory: 212k freed [ 517.264889] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 517.264891] Copyright (c) 1999-2006 Intel Corporation. [ 517.264939] PCI: Enabling device 0000:00:19.0 (0000 -> 0003) [ 517.264946] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 517.264959] PCI: Setting latency timer of device 0000:00:19.0 to 64 [ 517.282858] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:01:c8:f4 [ 517.327660] usbcore: registered new interface driver usbfs [ 517.327682] usbcore: registered new interface driver hub [ 517.327700] usbcore: registered new device driver usb [ 517.329647] USB Universal Host Controller Interface driver v3.0 [ 517.358234] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 517.358265] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 517.358274] PCI: Setting latency timer of device 0000:00:1a.0 to 64 [ 517.358277] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 517.358392] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 517.358417] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030c0 [ 517.358511] usb usb1: configuration #1 chosen from 1 choice [ 517.358530] hub 1-0:1.0: USB hub found [ 517.358534] hub 1-0:1.0: 2 ports detected [ 517.459061] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 [ 517.459074] PCI: Setting latency timer of device 0000:00:1a.1 to 64 [ 517.459077] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 517.459104] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 [ 517.459130] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030a0 [ 517.459240] usb usb2: configuration #1 chosen from 1 choice [ 517.459260] hub 2-0:1.0: USB hub found [ 517.459264] hub 2-0:1.0: 2 ports detected [ 517.560044] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 22 [ 517.560055] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 517.560059] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 517.560084] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 [ 517.560109] uhci_hcd 0000:00:1d.0: irq 22, io base 0x00003080 [ 517.560223] usb usb3: configuration #1 chosen from 1 choice [ 517.560242] hub 3-0:1.0: USB hub found [ 517.560246] hub 3-0:1.0: 2 ports detected [ 517.658793] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 517.658885] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 517.659594] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 517.661001] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 517.661009] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 517.661012] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 517.661032] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 [ 517.661055] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060 [ 517.661142] usb usb4: configuration #1 chosen from 1 choice [ 517.661163] hub 4-0:1.0: USB hub found [ 517.661167] hub 4-0:1.0: 2 ports detected [ 517.762063] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 517.762074] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 517.762079] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 517.762105] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 [ 517.762133] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040 [ 517.762245] usb usb5: configuration #1 chosen from 1 choice [ 517.762263] hub 5-0:1.0: USB hub found [ 517.762268] hub 5-0:1.0: 2 ports detected [ 517.863297] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 [ 517.863305] PCI: Setting latency timer of device 0000:00:1a.7 to 64 [ 517.863308] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 517.863328] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6 [ 517.867222] ehci_hcd 0000:00:1a.7: debug port 1 [ 517.867227] PCI: cache line size of 32 is not supported by device 0000:00:1a.7 [ 517.867230] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe2125c00 [ 517.877185] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 517.877261] usb usb6: configuration #1 chosen from 1 choice [ 517.877281] hub 6-0:1.0: USB hub found [ 517.877285] hub 6-0:1.0: 4 ports detected [ 517.978041] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 22 [ 517.978054] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 517.978058] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 517.978084] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 [ 517.979899] usb 4-2: new low speed USB device using uhci_hcd and address 2 [ 517.982000] ehci_hcd 0000:00:1d.7: debug port 1 [ 517.982005] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 517.982010] ehci_hcd 0000:00:1d.7: irq 22, io mem 0xe2125800 [ 517.990922] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 517.991030] usb usb7: configuration #1 chosen from 1 choice [ 517.991062] hub 7-0:1.0: USB hub found [ 517.991071] hub 7-0:1.0: 6 ports detected [ 518.563916] usb 4-2: new low speed USB device using uhci_hcd and address 3 [ 518.709959] usb 4-2: configuration #1 chosen from 1 choice [ 520.437702] input: HID 0566:3107 as /class/input/input3 [ 520.443835] input: USB HID v1.10 Keyboard [HID 0566:3107] on usb-0000:00:1d.1-2 [ 520.464571] input: HID 0566:3107 as /class/input/input4 [ 520.470830] input: USB HID v1.10 Device [HID 0566:3107] on usb-0000:00:1d.1-2 [ 520.470845] usbcore: registered new interface driver usbhid [ 520.470849] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 521.690719] EXT3 FS on sdb2, internal journal [ 522.043627] tun: Universal TUN/TAP device driver, 1.6 [ 522.043629] tun: (C) 1999-2004 Max Krasnyansky [ 522.216517] kjournald starting. Commit interval 5 seconds [ 522.216648] EXT3 FS on sdb1, internal journal [ 522.216651] EXT3-fs: mounted filesystem with ordered data mode. [ 522.271209] Adding 996020k swap on /dev/sdb4. Priority:-1 extents:1 across:996020k [ 527.390808] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 527.390813] e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO [ 530.905502] Bridge firewalling registered [ 530.905816] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. [ 530.906638] device eth0 entered promiscuous mode [ 530.951043] br0: port 1(eth0) entering learning state [ 545.946277] br0: topology change detected, propagating [ 545.946282] br0: port 1(eth0) entering forwarding state