000 (usable) [ 0.000000] user-defined physical RAM map: [ 0.000000] user: 0000000000000100 - 000000000008f000 (usable) [ 0.000000] user: 000000000008f000 - 00000000000a0000 (reserved) [ 0.000000] user: 0000000000100000 - 00000000c0000000 (usable) [ 0.000000] 2176MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000fe200 [ 0.000000] Entering add_active_range(0, 0, 786432) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 786432 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 786432 [ 0.000000] On node 0 totalpages: 786432 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 4352 pages used for memmap [ 0.000000] HighMem zone: 552704 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL ) [ 0.000000] ACPI: RSDT CFEFD038, 0050 (r1 INTEL DG965SS 6B7 1000013) [ 0.000000] ACPI: FACP CFEFC000, 0074 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: DSDT CFEF7000, 41AA (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: FACS CFE9C000, 0040 [ 0.000000] ACPI: APIC CFEF6000, 0078 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: WDDT CFEF5000, 0040 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: MCFG CFEF4000, 003C (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: ASF! CFEF3000, 00A6 (r32 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: HPET CFEF2000, 0038 (r1 INTEL DG965SS 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE9A000, 020C (r1 INTEL CpuPm 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE99000, 0175 (r1 INTEL Cpu0Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE98000, 0175 (r1 INTEL Cpu1Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE97000, 0175 (r1 INTEL Cpu2Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: SSDT CFE96000, 0175 (r1 INTEL Cpu3Ist 6B7 MSFT 1000013) [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at c4000000 (gap: c0000000:40000000) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 780288 [ 0.000000] Kernel command line: root=/dev/sdb2 mem=3G [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2397.669 MHz processor. [ 137.703899] Console: colour VGA+ 80x25 [ 137.703901] console [tty0] enabled [ 137.709995] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 137.710252] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 137.837809] Memory: 3115472k/3145728k available (1967k kernel code, 29036k reserved, 822k data, 208k init, 2228224k highmem) [ 137.837916] virtual kernel memory layout: [ 137.837917] fixmap : 0xffc55000 - 0xfffff000 (3752 kB) [ 137.837918] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 137.837919] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 137.837919] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 137.837920] .init : 0xc03bf000 - 0xc03f3000 ( 208 kB) [ 137.837921] .data : 0xc02ebe1d - 0xc03b962c ( 822 kB) [ 137.837922] .text : 0xc0100000 - 0xc02ebe1d (1967 kB) [ 137.838420] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 137.838726] hpet clockevent registered [ 137.898717] Calibrating delay using timer specific routine.. 4797.83 BogoMIPS (lpj=2398919) [ 137.898884] Mount-cache hash table entries: 512 [ 137.899041] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 137.899046] monitor/mwait feature present. [ 137.899108] using mwait in idle threads. [ 137.899172] CPU: L1 I cache: 32K, L1 D cache: 32K [ 137.899259] CPU: L2 cache: 4096K [ 137.899321] CPU: Physical Processor ID: 0 [ 137.899383] CPU: Processor Core ID: 0 [ 137.899445] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 137.899450] Intel machine check architecture supported. [ 137.899514] Intel machine check reporting enabled on CPU#0. [ 137.899579] Compat vDSO mapped to ffffe000. [ 137.899649] Checking 'hlt' instruction... OK. [ 137.902980] SMP alternatives: switching to UP code [ 137.903548] ACPI: Core revision 20070126 [ 137.905102] Parsing all Control Methods: [ 137.905192] Table [DSDT](id 0001) - 610 Objects with 62 Devices 154 Methods 38 Regions [ 137.905390] Parsing all Control Methods: [ 137.905474] Table [SSDT](id 0002) - 10 Objects with 0 Devices 4 Methods 0 Regions [ 137.905651] Parsing all Control Methods: [ 137.905741] Table [SSDT](id 0003) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 137.905917] Parsing all Control Methods: [ 137.906001] Table [SSDT](id 0004) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 137.906176] Parsing all Control Methods: [ 137.906260] Table [SSDT](id 0005) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 137.906435] Parsing all Control Methods: [ 137.906520] Table [SSDT](id 0006) - 5 Objects with 0 Devices 3 Methods 0 Regions [ 137.906677] tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired [ 137.906836] evxfevnt-0079 [00] enable : System is already in ACPI mode [ 137.907007] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 137.907130] SMP alternatives: switching to SMP code [ 137.907518] Booting processor 1/1 eip 3000 [ 137.918272] Initializing CPU#1 [ 137.977698] Calibrating delay using timer specific routine.. 4795.22 BogoMIPS (lpj=2397611) [ 137.977702] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000 [ 137.977706] monitor/mwait feature present. [ 137.977708] CPU: L1 I cache: 32K, L1 D cache: 32K [ 137.977709] CPU: L2 cache: 4096K [ 137.977711] CPU: Physical Processor ID: 0 [ 137.977712] CPU: Processor Core ID: 1 [ 137.977713] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000 [ 137.977717] Intel machine check architecture supported. [ 137.977719] Intel machine check reporting enabled on CPU#1. [ 137.978259] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 [ 137.978979] Total of 2 processors activated (9593.06 BogoMIPS). [ 137.979178] ENABLING IO-APIC IRQs [ 137.979397] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 138.090779] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 138.110875] Brought up 2 CPUs [ 138.110951] CPU0 attaching sched-domain: [ 138.110953] domain 0: span 00000003 [ 138.110954] groups: 00000001 00000002 [ 138.110957] CPU1 attaching sched-domain: [ 138.110958] domain 0: span 00000003 [ 138.110960] groups: 00000002 00000001 [ 138.111111] net_namespace: 64 bytes [ 138.111467] NET: Registered protocol family 16 [ 138.111632] ACPI: bus type pci registered [ 138.111755] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved [ 138.111819] PCI: Not using MMCONFIG. [ 138.113247] PCI: Using configuration type 1 [ 138.113309] Setting up standard PCI resources [ 138.120058] evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 [ 138.120775] evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 4 Runtime GPEs in this block [ 138.121684] ACPI: EC: Look up EC in DSDT [ 138.122935] Completing Region/Field/Buffer/Package initialization:........................................................................ [ 138.125324] Initialized 32/38 Regions 0/0 Fields 25/25 Buffers 15/35 Packages (649 nodes) [ 138.125482] Initializing Device/Processor/Thermal objects by executing _INI methods:. [ 138.125627] Executed 1 _INI methods requiring 0 _STA executions (examined 68 objects) [ 138.125797] ACPI: Interpreter enabled [ 138.125860] ACPI: (supports S0 S3 S5) [ 138.126003] ACPI: Using IOAPIC for interrupt routing [ 138.129376] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 138.130131] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO [ 138.130197] PCI quirk: region 0500-053f claimed by ICH6 GPIO [ 138.130841] PCI: Transparent bridge - 0000:00:1e.0 [ 138.130969] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 138.131237] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 138.131439] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 138.131524] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 138.131609] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT] [ 138.131692] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] [ 138.131776] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 138.136159] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.136624] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.137091] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.137553] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.138018] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.138482] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.138947] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.139409] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 138.139900] Linux Plug and Play Support v0.97 (c) Adam Belay [ 138.139984] pnp: PnP ACPI init [ 138.140049] ACPI: bus type pnp registered [ 138.142038] pnp: PnP ACPI: found 11 devices [ 138.142102] ACPI: ACPI bus type pnp unregistered [ 138.142300] SCSI subsystem initialized [ 138.142388] libata version 3.00 loaded. [ 138.142453] PCI: Using ACPI for IRQ routing [ 138.142516] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 138.146938] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 138.147112] hpet0: 3 64-bit timers, 14318180 Hz [ 138.148200] ACPI: RTC can wake from S4 [ 138.148751] Time: tsc clocksource has been installed. [ 138.151028] system 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved [ 138.151105] system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved [ 138.151171] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved [ 138.151237] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved [ 138.151302] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved [ 138.151368] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 138.151433] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved [ 138.151499] system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved [ 138.151564] system 00:01: iomem range 0xc0000-0xdffff could not be reserved [ 138.151630] system 00:01: iomem range 0xe0000-0xfffff could not be reserved [ 138.151700] system 00:06: ioport range 0x500-0x53f has been reserved [ 138.151765] system 00:06: ioport range 0x400-0x47f has been reserved [ 138.151830] system 00:06: ioport range 0x680-0x6ff has been reserved [ 138.182229] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0 [ 138.182329] PCI: Bridge: 0000:00:01.0 [ 138.182391] IO window: 2000-2fff [ 138.182454] MEM window: e0000000-e1ffffff [ 138.182517] PREFETCH window: d0000000-dfffffff [ 138.182581] PCI: Bridge: 0000:00:1c.0 [ 138.182643] IO window: disabled. [ 138.182706] MEM window: disabled. [ 138.182769] PREFETCH window: disabled. [ 138.182833] PCI: Bridge: 0000:00:1c.1 [ 138.182896] IO window: 1000-1fff [ 138.182959] MEM window: e2000000-e20fffff [ 138.183025] PREFETCH window: disabled. [ 138.183089] PCI: Bridge: 0000:00:1c.2 [ 138.183150] IO window: disabled. [ 138.183214] MEM window: disabled. [ 138.183276] PREFETCH window: disabled. [ 138.183340] PCI: Bridge: 0000:00:1c.3 [ 138.183402] IO window: disabled. [ 138.183465] MEM window: disabled. [ 138.183528] PREFETCH window: disabled. [ 138.183592] PCI: Bridge: 0000:00:1c.4 [ 138.183654] IO window: disabled. [ 138.183717] MEM window: disabled. [ 138.183780] PREFETCH window: disabled. [ 138.183844] PCI: Bridge: 0000:00:1e.0 [ 138.183905] IO window: disabled. [ 138.183969] MEM window: disabled. [ 138.184033] PREFETCH window: disabled. [ 138.184106] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 138.184230] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 138.184244] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 138.184369] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 138.184383] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16 [ 138.184508] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 138.184522] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 138.184647] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 138.184661] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 [ 138.184786] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 138.184799] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17 [ 138.184924] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 138.184932] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 138.184950] NET: Registered protocol family 2 [ 138.195265] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 138.195497] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 138.195881] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 138.196146] TCP: Hash tables configured (established 131072 bind 65536) [ 138.196217] TCP reno registered [ 138.199628] Machine check exception polling timer started. [ 138.199868] IA-32 Microcode Update Driver: v1.14a [ 138.200333] highmem bounce pool size: 64 pages [ 138.200397] Total HugeTLB memory allocated, 0 [ 138.200601] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 138.200701] io scheduler noop registered [ 138.200771] io scheduler cfq registered (default) [ 138.200925] Boot video device is 0000:01:00.0 [ 138.200996] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 138.201021] assign_interrupt_mode Found MSI capability [ 138.201104] Allocate Port Service[0000:00:01.0:pcie00] [ 138.201162] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 138.201194] assign_interrupt_mode Found MSI capability [ 138.201282] Allocate Port Service[0000:00:1c.0:pcie00] [ 138.201307] Allocate Port Service[0000:00:1c.0:pcie02] [ 138.201368] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 138.201400] assign_interrupt_mode Found MSI capability [ 138.201486] Allocate Port Service[0000:00:1c.1:pcie00] [ 138.201511] Allocate Port Service[0000:00:1c.1:pcie02] [ 138.201572] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 138.201604] assign_interrupt_mode Found MSI capability [ 138.201691] Allocate Port Service[0000:00:1c.2:pcie00] [ 138.201719] Allocate Port Service[0000:00:1c.2:pcie02] [ 138.201781] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 138.201812] assign_interrupt_mode Found MSI capability [ 138.201899] Allocate Port Service[0000:00:1c.3:pcie00] [ 138.201922] Allocate Port Service[0000:00:1c.3:pcie02] [ 138.201984] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 138.202016] assign_interrupt_mode Found MSI capability [ 138.202102] Allocate Port Service[0000:00:1c.4:pcie00] [ 138.202127] Allocate Port Service[0000:00:1c.4:pcie02] [ 138.202354] input: Power Button (FF) as /class/input/input0 [ 138.202418] ACPI: Power Button (FF) [PWRF] [ 138.202529] input: Sleep Button (CM) as /class/input/input1 [ 138.202596] ACPI: Sleep Button (CM) [SLPB] [ 138.202849] ACPI: Processor [CPU0] (supports 8 throttling states) [ 138.203039] ACPI: Processor [CPU1] (supports 8 throttling states) [ 138.203161] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 138.203320] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 138.226640] hpet_resources: 0xfed00000 is busy [ 138.226657] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI [ 138.226722] e100: Copyright(c) 1999-2006 Intel Corporation [ 138.227068] ahci 0000:00:1f.2: version 3.0 [ 138.227082] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19 [ 138.464018] Switched to high resolution mode on CPU 1 [ 138.464837] Switched to high resolution mode on CPU 0 [ 139.226655] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 139.226761] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part [ 139.226831] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 139.227003] scsi0 : ahci [ 139.227109] scsi1 : ahci [ 139.227215] scsi2 : ahci [ 139.227317] scsi3 : ahci [ 139.227418] scsi4 : ahci [ 139.227518] scsi5 : ahci [ 139.227682] ata1: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125100 irq 217 [ 139.227782] ata2: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125180 irq 217 [ 139.227884] ata3: DUMMY [ 139.227944] ata4: DUMMY [ 139.228005] ata5: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125300 irq 217 [ 139.228105] ata6: SATA max UDMA/133 abar m2048@0xe2125000 port 0xe2125380 irq 217 [ 139.683626] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 139.731135] ata1.00: ATA-7: ST3200820AS, 3.AAE, max UDMA/133 [ 139.731203] ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 139.789433] ata1.00: configured for UDMA/133 [ 140.244624] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 140.286583] ata2.00: ATA-7: ST3200820AS, 3.AAE, max UDMA/133 [ 140.286651] ata2.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 140.344880] ata2.00: configured for UDMA/133 [ 140.647589] ata5: SATA link down (SStatus 0 SControl 300) [ 140.950577] ata6: SATA link down (SStatus 0 SControl 300) [ 140.950737] scsi 0:0:0:0: Direct-Access ATA ST3200820AS 3.AA PQ: 0 ANSI: 5 [ 140.950939] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) [ 140.951011] sd 0:0:0:0: [sda] Write Protect is off [ 140.951075] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 140.951087] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 140.951220] sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) [ 140.951291] sd 0:0:0:0: [sda] Write Protect is off [ 140.951354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 140.951366] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 140.951467] sda: sda1 [ 140.970179] sd 0:0:0:0: [sda] Attached SCSI disk [ 140.970311] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 140.970449] scsi 1:0:0:0: Direct-Access ATA ST3200820AS 3.AA PQ: 0 ANSI: 5 [ 140.971381] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB) [ 140.971452] sd 1:0:0:0: [sdb] Write Protect is off [ 140.971516] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 140.971528] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 140.971657] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB) [ 140.971728] sd 1:0:0:0: [sdb] Write Protect is off [ 140.971791] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 140.971803] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 140.971903] sdb: sdb1 sdb2 sdb3 sdb4 [ 140.992793] sd 1:0:0:0: [sdb] Attached SCSI disk [ 140.992904] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 140.993077] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 140.993219] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 140.993243] scsi6 : pata_marvell [ 140.993347] scsi7 : pata_marvell [ 140.993441] ata7: PATA max UDMA/100 cmd 0x1018 ctl 0x1024 bmdma 0x1000 irq 17 [ 140.993507] ata8: DUMMY [ 140.993584] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00 [ 141.298922] ata7.00: ATAPI: HL-DT-ST DVDRAM GSA-H42N, RL00, max UDMA/66 [ 141.455919] ata7.00: configured for UDMA/66 [ 141.459380] scsi 6:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H42N RL00 PQ: 0 ANSI: 5 [ 141.476858] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 141.476963] Uniform CD-ROM driver Revision: 3.20 [ 141.477110] sr 6:0:0:0: Attached scsi CD-ROM sr0 [ 141.477160] sr 6:0:0:0: Attached scsi generic sg2 type 5 [ 141.477343] PNP: PS/2 Controller [PNP0f03:PS2M] at 0x60,0x64 irq 12 [ 141.477407] PNP: PS/2 controller doesn't have KBD irq; using default 1 [ 141.480329] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 141.480394] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 141.480522] mice: PS/2 mouse device common for all mice [ 141.660640] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) [ 142.301652] input: ImPS/2 Generic Wheel Mouse as /class/input/input2 [ 142.314441] iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0460) [ 142.314592] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 142.314669] iTCO_vendor_support: vendor-support=0 [ 142.314773] TCP cubic registered [ 142.314841] NET: Registered protocol family 1 [ 142.314910] NET: Registered protocol family 17 [ 142.314975] Using IPI No-Shortcut mode [ 142.315114] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 142.315178] EDD information not available. [ 142.326370] EXT3-fs: INFO: recovery required on readonly filesystem. [ 142.326436] EXT3-fs: write access will be enabled during recovery. [ 142.392504] kjournald starting. Commit interval 5 seconds [ 142.392510] EXT3-fs: recovery complete. [ 142.396013] EXT3-fs: mounted filesystem with ordered data mode. [ 142.396087] VFS: Mounted root (ext3 filesystem) readonly. [ 142.396242] Freeing unused kernel memory: 208k freed [ 145.035592] uhci_hcd: Unknown symbol usb_hcd_pci_suspend [ 145.035628] uhci_hcd: Unknown symbol usb_hcd_resume_root_hub [ 145.035651] uhci_hcd: Unknown symbol usb_hcd_pci_probe [ 145.035674] uhci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep [ 145.035738] uhci_hcd: Unknown symbol usb_disabled [ 145.035810] uhci_hcd: Unknown symbol usb_hcd_check_unlink_urb [ 145.035852] uhci_hcd: Unknown symbol usb_calc_bus_time [ 145.035886] uhci_hcd: Unknown symbol usb_hcd_link_urb_to_ep [ 145.035911] uhci_hcd: Unknown symbol usb_hcd_pci_resume [ 145.035967] uhci_hcd: Unknown symbol usb_hcd_giveback_urb [ 145.036003] uhci_hcd: Unknown symbol usb_hcd_poll_rh_status [ 145.036048] uhci_hcd: Unknown symbol usb_hcd_pci_remove [ 145.036079] uhci_hcd: Unknown symbol usb_root_hub_lost_power [ 145.036688] usbcore: registered new interface driver usbfs [ 145.036709] usbcore: registered new interface driver hub [ 145.036728] usbcore: registered new device driver usb [ 145.038832] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 [ 145.038842] PCI: Setting latency timer of device 0000:00:1a.7 to 64 [ 145.038845] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 145.038968] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 145.042354] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 145.042357] Copyright (c) 1999-2006 Intel Corporation. [ 145.042866] ehci_hcd 0000:00:1a.7: debug port 1 [ 145.042871] PCI: cache line size of 32 is not supported by device 0000:00:1a.7 [ 145.042879] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe2125c00 [ 145.052423] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 145.052556] usb usb1: configuration #1 chosen from 1 choice [ 145.052584] hub 1-0:1.0: USB hub found [ 145.052591] hub 1-0:1.0: 4 ports detected [ 145.153538] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 [ 145.153550] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 145.153554] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 145.153582] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 145.157491] ehci_hcd 0000:00:1d.7: debug port 1 [ 145.157496] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 145.157503] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe2125800 [ 145.166396] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 145.166492] usb usb2: configuration #1 chosen from 1 choice [ 145.166512] hub 2-0:1.0: USB hub found [ 145.166519] hub 2-0:1.0: 6 ports detected [ 145.168539] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 145.168632] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 145.169401] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 145.267602] PCI: Enabling device 0000:00:19.0 (0000 -> 0003) [ 145.267611] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 21 [ 145.267623] PCI: Setting latency timer of device 0000:00:19.0 to 64 [ 145.285300] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:01:c8:f4 [ 145.360471] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 146.028386] USB Universal Host Controller Interface driver v3.0 [ 146.028426] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 146.028434] PCI: Setting latency timer of device 0000:00:1a.0 to 64 [ 146.028437] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 146.028461] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 146.028485] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030c0 [ 146.028572] usb usb3: configuration #1 chosen from 1 choice [ 146.028592] hub 3-0:1.0: USB hub found [ 146.028596] hub 3-0:1.0: 2 ports detected [ 146.129497] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 22 [ 146.129508] PCI: Setting latency timer of device 0000:00:1a.1 to 64 [ 146.129512] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 146.129538] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 146.129563] uhci_hcd 0000:00:1a.1: irq 22, io base 0x000030a0 [ 146.129675] usb usb4: configuration #1 chosen from 1 choice [ 146.129694] hub 4-0:1.0: USB hub found [ 146.129698] hub 4-0:1.0: 2 ports detected [ 146.230463] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 [ 146.230471] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 146.230474] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 146.230497] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 [ 146.230519] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00003080 [ 146.230639] usb usb5: configuration #1 chosen from 1 choice [ 146.230659] hub 5-0:1.0: USB hub found [ 146.230664] hub 5-0:1.0: 2 ports detected [ 146.331500] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 146.331511] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 146.331515] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 146.331540] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 [ 146.331568] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060 [ 146.331676] usb usb6: configuration #1 chosen from 1 choice [ 146.331695] hub 6-0:1.0: USB hub found [ 146.331700] hub 6-0:1.0: 2 ports detected [ 146.432471] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 146.432481] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 146.432485] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 146.432510] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 [ 146.432532] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040 [ 146.432645] usb usb7: configuration #1 chosen from 1 choice [ 146.432664] hub 7-0:1.0: USB hub found [ 146.432668] hub 7-0:1.0: 2 ports detected [ 146.638364] usb 6-2: new low speed USB device using uhci_hcd and address 2 [ 146.782600] usb 6-2: configuration #1 chosen from 1 choice [ 146.852730] input: HID 0566:3107 as /class/input/input3 [ 146.859376] input: USB HID v1.10 Keyboard [HID 0566:3107] on usb-0000:00:1d.1-2 [ 146.879578] input: HID 0566:3107 as /class/input/input4 [ 146.886371] input: USB HID v1.10 Device [HID 0566:3107] on usb-0000:00:1d.1-2 [ 146.886386] usbcore: registered new interface driver usbhid [ 146.886389] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 149.290322] EXT3 FS on sdb2, internal journal [ 149.680968] tun: Universal TUN/TAP device driver, 1.6 [ 149.680971] tun: (C) 1999-2004 Max Krasnyansky [ 149.952958] kjournald starting. Commit interval 5 seconds [ 149.953131] EXT3 FS on sdb1, internal journal [ 149.953136] EXT3-fs: mounted filesystem with ordered data mode. [ 150.007648] Adding 996020k swap on /dev/sdb4. Priority:-1 extents:1 across:996020k [ 155.052320] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 155.052324] e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO [ 158.607112] Bridge firewalling registered [ 158.607406] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. [ 158.608230] device eth0 entered promiscuous mode [ 158.662029] br0: port 1(eth0) entering learning state [ 173.657878] br0: topology change detected, propagating [ 173.657884] br0: port 1(eth0) entering forwarding state